Granulator As the production of crucial
gear, its use and upkeep, upkeep is specifically crucial. Here's what
Granulator use and maintenance, maintenance.
One particular that mixed the general
perform approach
2, granulating process for attention 1.
Material within the granulation have to undergo a conditioning, steam pressure
is to stabilize (4-8bar), as well as the steam just before the transfer have to
be in addition to water good quality, if the steam contains a good deal of
water, will cause granulation from the plug. Components soon after
conditioning, there have already been a specific degree of maturation, can
considerably enhance the utilization of feed nutrients.
two. Granulation procedure, the supplies
must often check the humidity and temperature. Humidity method to verify is:
hand-Qing Nie, the material may be within the piece as well. Species as a
result of granulation temperature to vary, to stabilize the manage in 75? 95
amongst.
3. Right after pelleting the particles have
to not be excessive cooling or cooling just isn't enough, if cooled also
quickly, make material particle surface cracking, cool sufficient, the
temperature is also high, material will absorb moisture causing mold block.
Following cooling, the material need to be consistent together with the room
temperature.
1. Ring mold material is normally carbon
steel, alloy steel or Stainless steel , Based on materials corrosion and
ring-mode intensity of function to select the ring mode in the material, on the
corrosion of components as well as a small ring mold hole normally use
stainless steel ring mold. Roller material typically employed within the carbon
steel or alloy steel. Or concave type tooth may be employed for Pass.
two. Ring flat
die briquettes machine compression ratio. Ring mold
ring mold compression ratio is the effective operating length and flat
die briquettes machine diameter ratio. Raw supplies
and goods according to requirements formula to select the ring mode of the
compression ratio. Low compression ratio can enhance production, decrease
energy consumption, reduce the ring flat
die briquettes machine and roller wear.
Nonetheless, loose particles, of various lengths, feed powder rate; contrary
particle strong, smooth and shiny appearance, chalking tiny, but higher
production fees. Users can select according to their wants than the compression
ring mold, animal pellet compression ring mold normally significantly less than
ten, the ring flat
die briquettes machine pellet feed aquatic
compression ratio more than 10.
Model for some little holes within the
ring, ring mold to ensure the strength on the premise of making certain a
reasonable compression, increasing the thickness on the ring mold and decompression
of far more correct holes.
four, the correct operation, upkeep pellet
mill
1. Ring flat
die briquettes machine and roller gap adjustment
ring for the new model and adjust the roller gap, the ring mold and should be
the highest roller slight make contact with roller to achieve "may
transfer non-transfer" state. If adjustments in the operate of state,
could be acceptable ring mode and increasing the stress roller, but surely
enough is adequate. Ring flat
die briquettes machine and roller gap is also big,
stress roller can not rotate, resulting in blocking Charcoal
machine. Ring flat
die briquettes machine and roller gap is too tiny,
will boost the ring flat
die briquettes machine and roller put on, load up,
a significant trigger ring flat
die briquettes machine and roller damage. Need to
promptly check the ring mold and roller gaps, at least check once each and
every four functioning hours. When adjusting the various rollers, pay focus to
the direction of each and every roller adjustment should be created relative
towards the pellet mill roller shaft torque and zero, to ensure that pellet
mill in the asymmetry of energy.
2. Frequency of team upkeep Granulator each
class must be completed prior to the inspection, verify the transmission
components, instruments, Valve Doors, raises oil (Jg with lithium lubricants),
and eliminate iron on iron filings.
three. Properly installed or replace the
ring flat
die briquettes machine and roller is actually a new
model with the new general roll, roll the old model using the old, to be able
to ring flat
die briquettes machine and roller profiling state
close to the surface shape, ring flat
die briquettes machine and roller of all similar
local space . In order that the entire force, as well as a ring mold material
are extremely uniform, can boost production efficiency.
没有评论:
发表评论